Handbook of Building Construction: Data for Architects, Designing and Constructing Engineers, and Contractors ...George A. Hool, Nathan C. Johnson McGraw-Hill Book Company, Incorporated, 1920 |
No interior do livro
Resultados 1-5 de 100
Página 805
... Heat - ventilation - rough 22 Heat - regulation - finish 9-10 1-8 12-20 2-25 6-20 7-10 7-20 23 Electric - rough - temp . light 9-10 1-8 9-1 9-20 10-30 24 Electric - fixtures 12-20 2-25 7-10 7-30 8-10 25 Common brick masonry 9-25 12-20 7 ...
... Heat - ventilation - rough 22 Heat - regulation - finish 9-10 1-8 12-20 2-25 6-20 7-10 7-20 23 Electric - rough - temp . light 9-10 1-8 9-1 9-20 10-30 24 Electric - fixtures 12-20 2-25 7-10 7-30 8-10 25 Common brick masonry 9-25 12-20 7 ...
Página 823
... heat will have to be supplied by means of coke or coal fires in salamanders , the heat thus produced being confined within the building by a liberal use of canvas , or other protection around the exterior at the level at which the work ...
... heat will have to be supplied by means of coke or coal fires in salamanders , the heat thus produced being confined within the building by a liberal use of canvas , or other protection around the exterior at the level at which the work ...
Página 844
... heat and shock and for this reason is not used full strength . Dynamite is any absorbent material saturated , or partly saturated , with nitroglycerin . It is known as " active " or " inactive " according to the nature of the absorbent ...
... heat and shock and for this reason is not used full strength . Dynamite is any absorbent material saturated , or partly saturated , with nitroglycerin . It is known as " active " or " inactive " according to the nature of the absorbent ...
Página 883
... heat the tube to vaporize the spray . This is accomplished by collecting a small quantity of the fuel on the tray and igniting it . Initial heating only is required as the heat from the light itself is sufficient to heat the tube after ...
... heat the tube to vaporize the spray . This is accomplished by collecting a small quantity of the fuel on the tray and igniting it . Initial heating only is required as the heat from the light itself is sufficient to heat the tube after ...
Página 889
... heat , avoidance of extremely high temperatures , prevention of draughts of outside air , and the use of steam baths before drying are factors tending to reduce the tendency to brittleness . 5. Effect of Defects on Strength of Timber ...
... heat , avoidance of extremely high temperatures , prevention of draughts of outside air , and the use of steam baths before drying are factors tending to reduce the tendency to brittleness . 5. Effect of Defects on Strength of Timber ...
Outras edições - Ver tudo
Handbook of Building Construction: Data for Architects, Designing and ... George A. Hool,Nathan C. Johnson Visualização integral - 1920 |
Handbook of Building Construction: Data for Architects, Designing and ... George A. Hool,Nathan C. Johnson Visualização integral - 1920 |
Handbook of Building Construction: Data for Architects, Designing and ... George A. Hool,Nathan C. Johnson Visualização integral - 1920 |
Palavras e frases frequentes
ammonia amount amperes architect average bars boiler brick building calcined candle power capacity cement circuit coat color column compressive compressive strength concrete connection construction contract contractor cost diameter door drain elastic limit electric elevator engine estimated feet finish fixtures floor flue foot foot-candles gage glass grade gray iron gypsum heat hydrated lime illumination inches installed iron joints lamp lath length less light lime limestone load machine manufacture material metal method mortar motor operation outlet paint pile pipe placed plaster plumbing Portland cement pounds pressure proper pump quantity radiation reciprocating engine reinforced roof sand sewer sheet specific gravity specifications square standard steam steel stone strength structural stucco surface Table tank temperature tensile strength terra cotta thickness tile timber trap usually vacuum valve velocity vent wall weight width wire wood
Passagens conhecidas
Página 1390 - Portland cement is the product obtained by finely pulverizing clinker produced by calcining to incipient fusion an intimate and properly proportioned mixture of argillaceous and calcareous materials, with no additions subsequent to calcination excepting water and calcined or uncalcined gypsum.
Página 1398 - If the percentage of elongation of any tension test specimen is less than that specified in Sec. 8(a) and any part of the fracture is outside the middle third of the gage length, as indicated by scribe scratches marked on the specimen before testing, a retest shall be allowed.
Página 1390 - The cement shall be stored in such a manner as to permit easy access for proper inspection and identification of each shipment, and in a suitable weather-tight building which will protect the cement from dampness.
Página 1398 - The inspector representing the purchaser shall have free entry, at all times while work on the contract of the purchaser is being performed, to all parts of the manufacturer's works which concern the manufacture of the material ordered.
Página 1242 - place of employment," shall mean and include every place, whether indoors or out, or underground, and the premises appurtenant thereto where either temporarily or permanently any industry, trade or business, is carried on, or where any process or operation, directly or indirectly related to any industry, trade or business, is carried on, and where any person is directly or indirectly employed by another for direct or indirect gain or profit but shall not include any place where persons are employed...
Página 891 - In cases where timbers do not contain the pith and it is impossible to locate it with any degree of accuracy, the same inspection shall be made over 3...
Página 890 - ... and is so fixed by growth or position that it will retain its place in the piece.
Página 1392 - If any test specimen shows defective machining or develops flaws, it may be discarded and another specimen substituted. (c) If the percentage of elongation of any tension test specimen is less than that specified in Section 5 (a) and any part of the fracture is more than % in.
Página 1393 - Section 4, which represent rejected material, shall be preserved for two weeks from the date of the test report. In case of dissatisfaction with the results of the tests, the manufacturer may make claim for a rehearing within that time.
Página 1062 - Work, and will endeavor to guard the Owner against defects and deficiencies in the Work of the Contractor.